Certo, ad occhio non sembra una cosa semplice, comunque, dategli un'occhiata:
Link Bad Axe rev. 302 Conroe support mod
Buona lettura!
Certo, ad occhio non sembra una cosa semplice, comunque, dategli un'occhiata:
Link Bad Axe rev. 302 Conroe support mod
Buona lettura!
Più che altro c'è da perderci la vista... Ci vuole un saldatore come si deve.
Questa è la storia di 4 persone chiamate Ognuno, Qualcuno, Ciascuno e Nessuno. C'era un lavoro importante da fare e Ognuno era sicuro che Qualcuno lo avrebbe fatto. Ciascuno poteva farlo, ma Nessuno lo fece, Qualcuno si arrabbiò perché era il lavoro di Ognuno. Ognuno pensò che Ciascuno potesse farlo, ma Ognuno capì che Nessuno l'avrebbe fatto. Finì che Ognuno incolpò Qualcuno perché Nessuno fece ciò che Ciascuno avrebbe potuto fare.
e io mi chiedo..
ma come ha fatto a scoprire come fare questa modifica?
ci vogliono saldatori e mano ferma per fare lavori di così fine saldatura, di certo non alla portata di tutti!
betaxp86
perchè glie le hanno dette o lavora per loro...Originariamente inviato da betaxp86
"Scusate, ma se quest'anno in Texas ci avete spedito questo deficiente, vuol dire che c'è speranza per tutti?"
Cmq è sicuro. La dritta è arrivata da qualcuno che ha gli schemi della mobo. Non è una "semplice" vmod...Originariamente inviato da giampa
Questa è la storia di 4 persone chiamate Ognuno, Qualcuno, Ciascuno e Nessuno. C'era un lavoro importante da fare e Ognuno era sicuro che Qualcuno lo avrebbe fatto. Ciascuno poteva farlo, ma Nessuno lo fece, Qualcuno si arrabbiò perché era il lavoro di Ognuno. Ognuno pensò che Ciascuno potesse farlo, ma Ognuno capì che Nessuno l'avrebbe fatto. Finì che Ognuno incolpò Qualcuno perché Nessuno fece ciò che Ciascuno avrebbe potuto fare.
Ragazzi,
freecableguy ha aggiornato il thread con altre 2 mod molto interessanti (una è d'obbligo).
Le riporto perchè si possono fare anche sulla rev. 304.
Eccole:
Vcore "Modification" - unlocked BIOS for ALL chips (optional)
Notice the 3-pin header called "BIOS CONFIG" used for flashing and maintenance mode. Now...notice the empty silk-screen locations (OC DEBUG) above that in the picture? Intel has purposefully not shown the through-holes in their pictures as they have been blacked out. (I have shown them with the yellow circles.)
Mod: Short together the holes shown. Use either conductive ink or solder. If you wish, install a header and use an extra shorting bar from your included accessories to make this mod changable!
When you boot and enter the BIOS you will have full control over CPU VID (vcore), Enhanced Power Slope (reduces vdroop to 50% default), and Default Bus Override (533, 800, 1066, 1333Mhz) with the ability to go 30% over your set FSB! ClockGen also works with the ICS 954123 PLL chip. Please donate if you find the program useful.
Note: This mod can be done on the newer rev. 304 board also!
Vddr Modification - up to ~2.8V for your DDR2 (optional)
A special thanks to Tarosa, PRTeamJapan and all the members of Team Japan for their work in creating this modification
Mod: Connect a 100K ohm potentiometer from Pin #1 of U6H1 (SC2612E) to GND. Set to maximum resistance before connecting. Lower resistance to raise volts. It is recommended that a separate 220ohm resistor be added to the VR in parallel to prevent grounding Pin #1. This allow for ~2.8V (voltaggio "insane" ndr.... ) to your DDR2. Make sure you know what your memory can handle before you put excessive voltage to it!
Note: This mod can be done on the newer rev. 304 board also!
Altre mod, per chi, invece di phase, decide di andarci pesante con il freddo.
Occhio che IMHO con Azoto sono obbligatorie (almeno la seconda)...
Extreme Vcore Modification (not recommended for those not using LN2)
"A special thanks to TAM and all the members of Team Japan for their work in creating this modification!!!
Complete Image 3. Vcore "Modification" - unlocked BIOS for ALL chips before making this modification. That step allows selection of 1.6v by BIOS (~1.565v real) for the CPU. This is more than enought to carry most users to maximum clock with their Conroe CPU. If you have more exotic cooling (read: LN2) then complete this modification and the one below, if desired, to allow for manual temperature offset.
Mod: Connect a 50K ohm potentiometer (set at maximum resistance) rrom Pin #4 (red points) of ADP3189 to GND. Lower resistance to increase Vcore. This allows for ~0.2v increase over BIOS values (~1.75v real) at 6K ohm. Lower settings cause a shutdown on voltage protection (a modification is being worked to get around this). The green dot shows the measure point (to ground) for Vcore.
Note: This mod can be done on the newer rev. 304 board also!"
Tcore Modification (not recommended for those not using LN2 or other cooling > -127C)
A special thanks to OMEGA and all the members of Team Japan for their work in creating this modification!!!
The onboard thermal diode is monitored by the SMSC EMC6D103CZC and allows reading temperatures as low as -127C (1/2 of an unsigned 8-bit boundry). This modification allows for a manual positive offset.
Mod: Remove the resistor from the pad shown below and solder a 200 ohm potentiometer in place. Set to 100 ohms for ~30C increase. More resistance creates a bigger positive thermal reading offset. Do not set too high or you may run into problems with water or air cooling (remember to set back when you don't need the offset).
Allowing the thermal diode to go below -127C will cause the board to alarm and shutdown on thermal protection. This allows LN2/cascade users to go MUCH lower. (Using bigger VRs may allow for an even bigger maximum tunable offset.)
Note: This mod can be done on the newer rev. 304 board also! Notice that you can see some of the SMT resistors soldered to a rev. 302 board in this pic. (The components soldered in place are even bigger than those called out in the guide steps 1-3 above!)
Buon divertimento.....
Quante ne hai ordinate Carmine????
Ci sono attualmente 1 utenti che stanno visualizzando questa discussione. (0 utenti e 1 ospiti)